Introduction: Furniture Restoration: Decoupage Removal and Refinishing

In this instructable, I volition exist showing you how I transformed this dresser and dark stand. These items were definitely the biggest fixer uppers I've gotten and so far, simply I got them for complimentary so I'm not complaining. The items were covered in decoupage considering the previous owners had attempted to cover the tops and drawers with fabric. There were as well extra holes in the drawers that the previous owners had made to change out the drawer pulls with knobs. There was likewise just an incredible amount of crud stuck into the intricate detailing of the furniture. Watch the 3 minute video to a higher place to see how I fixed this or keep reading below.

Step 1: Gather Your Supplies

For this project, I used:

  • Goof Off Pro Strength Remover: https://amzn.to/2Xcxi0U
  • Ryobi Sander: https://amzn.to/2JXEz2W
  • Sander Sandpaper: https://amzn.to/2HRKxk0
  • Stain https://amzn.to/2UxO5yN
  • Paintbrush: https://amzn.to/2WxwCD0
  • Drop Cloth: https://amzn.to/2Uqej5h
  • Kleenex Hand Towels https://amzn.to/2UpwQ1n (these are more durable than paper towels and practise not go out behind residual on the furniture)
  • Mineral Spirits https://amzn.to/2Usd5qN
  • Polyurethane Protective Terminate https://amzn.to/2UqP4R4
  • Old English Scratch Comprehend For Dark Woods https://amzn.to/2I781Rm
  • Old English Scratch Comprehend For Low-cal Woods https://amzn.to/2VcbS3j

Pace ii: Remove the Decoupage and Cease

I started by applying goof off pro forcefulness remover to the decoupage and used a paper towel to wipe it off. This removed near of the decoupage. I and so used a sander with an 80 grit sanding pad to remove the residual of the decoupage along with the original finish. I as well had to use a utility knife to get the decoupage out of the grooves. I only removed the finish on the tops and the drawers since this was where the decoupage had been. Ideally I should take removed the finish on the entire pieces of article of furniture to have a more than compatible colour upon restaining, but it was going to be also difficult to remove the finish on some of the intricate detailing.

Footstep 3: Gear up the Wood for Restaining

After all of the decoupage and original end were removed, I worked my way upward to a 220 grit on the sander to set the wood to be restained. I and then used a make clean rag dampened with mineral spirits to wipe off the sanding debris.

Step 4: Fill the Extra Holes With Wood Putty

I and then used wood putty to fill in the extra holes in the drawers and immune that to gear up for 24 hours.

Step v: Apply the Stain

I placed a drop textile underneath the furniture to protect the ground from the stain. I then practical a thick layer of Varathane classic wood stain in the direction of the grain on the tops and drawers of the furniture, making sure to do and so in a well ventilated area. I then wiped the backlog stain off with a Kleenex hand towel. I waited for two hours before applying another glaze.

Footstep 6: Clean the Brush

I cleaned my castor off with mineral spirits after each application of stain. (This should also be washed in a well ventilated area. I poured the mineral spirits into a paper plate and agitated my brush in the product until all the residue had dissolved. I pressed out the excess, wiped information technology with a clean towel, and laid it out to dry.

Step vii: Apply the Protective Finish

I so waited 24 hours before applying Varathane Polyurethane protective finish in the direction of the grain. (This should also be done in a well ventilated surface area). I waited ii hours before applying a second coat.

Step 8: Clean the Grime

Later on allowing the second coat of terminate to dry for 2 hours, I used Old English Scratch cover on a toothbrush to clean the grime off of the intricate detailing of the furniture. This is not the intended use for this product, merely it is safety on wood and it hides any scratches on the furniture at the same time as I clean it.

Step 9: Attach Drawer Pulls

Lastly, I added new drawer pulls to the furniture.

Step 10: Finished!

And that'south all information technology took to transform this dresser and nightstand! If you enjoyed this tutorial, please consider following me on Instructables and subscribing to my Youtube channel to see more content similar this. https://world wide web.youtube.com/channel/UCMQQAmEG3HaUyNFHi...

Be the Offset to Share

Recommendations

  • Anything Goes Contest

    Anything Goes Contest